| Chuck out of SLC, UT! | |
|
|
Author | Message |
---|
BOOSTJUNKY
Posts : 6 Join date : 2009-10-09
| Subject: Chuck out of SLC, UT! Fri Oct 09, 2009 12:36 am | |
| Hey guys! Glad to be here! I'm Chuck (aka: Chuck's_srt-4), in case you didn't already figure that out! Can't wait to see how this forum turns out.
I also can't wait to finally get my SRT all set up, and down the track with a built motor! Enough of this stock motor crap!
Currently I'm waiting on the bottom end fasteners (H11 studs from DCR) to show up, and once they arrive along with the 5-Layer head gasket, it's game on! | |
|
| |
DSCRACING Admin
Posts : 219 Join date : 2009-09-24 Age : 43 Location : Charlotte N.C.
| Subject: Re: Chuck out of SLC, UT! Fri Oct 09, 2009 2:56 am | |
| My man! Tell everyone what a stock srt4 motor can put down Chuck! Lol This is getting fun again... | |
|
| |
BOOSTJUNKY
Posts : 6 Join date : 2009-10-09
| Subject: Re: Chuck out of SLC, UT! Fri Oct 09, 2009 3:13 am | |
| UNCORRECTED @ approx. 4300 ft. elevation! Done on 32 psi! | |
|
| |
DSCRACING Admin
Posts : 219 Join date : 2009-09-24 Age : 43 Location : Charlotte N.C.
| Subject: Re: Chuck out of SLC, UT! Fri Oct 09, 2009 3:28 am | |
| Your rods called me after all that... I don't think they like you anymore!! But thats ok, Your new ones can put up with alot more abuse! Quote of the day.. " If your not on the edge, your taking up to much space!" | |
|
| |
BOOSTJUNKY
Posts : 6 Join date : 2009-10-09
| Subject: Re: Chuck out of SLC, UT! Fri Oct 09, 2009 4:08 am | |
| | |
|
| |
Samlilly2 Admin
Posts : 131 Join date : 2009-09-25 Age : 39 Location : Goldsboro, NC
| Subject: Re: Chuck out of SLC, UT! Fri Oct 09, 2009 9:48 am | |
| Welcome Man. Good to see you on here. If you have any friends invite them on up. -Sammie | |
|
| |
DSCRACING Admin
Posts : 219 Join date : 2009-09-24 Age : 43 Location : Charlotte N.C.
| Subject: Re: Chuck out of SLC, UT! Fri Oct 09, 2009 3:30 pm | |
| Thats funny stuff! Normally stock rods don't bend like that. You got very lucky. | |
|
| |
Samlilly2 Admin
Posts : 131 Join date : 2009-09-25 Age : 39 Location : Goldsboro, NC
| Subject: Re: Chuck out of SLC, UT! Fri Oct 09, 2009 4:31 pm | |
| - DSCRACING wrote:
- Thats funny stuff! Normally stock rods don't bend like that. You got very lucky.
Yeah, I have only seen something like that is the engine was Hydrolocked. Oh those were the days of F&F when everyone and their mother had to have "Cold Air" intakes. -Sammie | |
|
| |
DSCRACING Admin
Posts : 219 Join date : 2009-09-24 Age : 43 Location : Charlotte N.C.
| Subject: Re: Chuck out of SLC, UT! Fri Oct 09, 2009 5:25 pm | |
| I've seen it alot but mainly on billet rods | |
|
| |
BOOSTJUNKY
Posts : 6 Join date : 2009-10-09
| Subject: Re: Chuck out of SLC, UT! Fri Oct 09, 2009 7:57 pm | |
| | |
|
| |
DSCRACING Admin
Posts : 219 Join date : 2009-09-24 Age : 43 Location : Charlotte N.C.
| Subject: Re: Chuck out of SLC, UT! Sat Oct 10, 2009 1:40 pm | |
| Nice! Any motor I've seen dish out 100+ pounds of boost is cool in my book. Great job Chuck. | |
|
| |
Sponsored content
| Subject: Re: Chuck out of SLC, UT! | |
| |
|
| |
| Chuck out of SLC, UT! | |
|